Cooper Lighting Indoor Furnishings BCHE User Manual

BC, BW, BWVE, BCVE,  
BCHE, BWHE, SERIES LUMINAIRES  
INCANDESCENT AND COMPACT  
FLUORESCENT  
INSTALLATION INSTRUCTIONS  
IMPORTANT: Read carefully before installing fixture.  
Retain for future reference.  
6/93  
IMI-313  
General: Upon receipt of fixture thoroughly inspect for  
any freight damage, which should be brought to the  
attention of the delivering carrier. Compare the catalog  
description listed on the packing slip with the fixture  
label on the housing to assure you have received the  
correct merchandise.  
Safety: This fixture must be wired in accordance with  
the National Electrical Code and applicable local codes  
and ordinances. Proper grounding is required to insure  
personal safety. Carefully observe grounding procedure  
under installation section. All work should be done by a  
qualified electrician.  
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.  
CLEANING: The reflector and lens may be cleaned with any non-abrasive cloth  
and mild detergent (i.e. 409 Cleaner). Cleaning should be done on the lens at room  
temperature, and out of direct sunlight. To remove paint, lipstick, marker, etc., the  
following solvents may be used:  
RECOMMENDED: a solution of three (3) parts alcohol, one (1) part TOLUOL.  
OR: four (4) parts alcohol, one part Methylethylketone (MEK).  
Also safe, but less effective: Naphtha, Butyl Cellosolve, Kerosene.  
NEVER USE: Gasoline, Benzene, Acetone, Carbon Tetrachloride or highly  
alkaline cleaners. Never clean Luminaire while energized, or while lens is  
hot.  
WARNING: If the lens has a Factory-applied trim color, these solvents will also remove this paint.  
Replacement of the entire lens is recommended in this case.  
1. Remove lens, using a torx screwdriver (for screws with center-pin).  
2. Remove the four 5/10” knock-outs.  
3. Determine correct fasteners to use for the mounting surface. Fasteners should be 1/4” normal.  
4. The mounting gasket may be used as a template to lay out the fastener locations.  
5. Make wiring connections.  
6. Place two of the mounting screws through the mounting plate, and position the mounting gasket into position  
on the back (wall-side) of the plate.  
7. Position mounting plate on wall in one of the “UP” orientations, according to the embossed arrows on the  
mounting plate. Check position of internal reflector, if equipped (see Note).  
8. Start mounting fasteners but do not tighten.  
1
9. Check the gasket position. At least /4 of gasket should extend beyond the mounting plate, all the way around.  
10. Tighten all four mounting fasteners.  
11. Install lamp. Screw base lamps should be tightened, then loosened one to two turns, then re-tightened. This  
will properly seat the lamp for best mechanical and electrical connection.  
12. Replace lens, tighten screws.  
NOTE: For optional Internal Reflectors  
If the fixture has a reflector attached to the mounting plate, it should be positioned above the lamp. If the lens  
has a portion “Painted Out” to form an “Eyelid”, this portion should be positioned toward the ceiling, and over  
the internal reflector.  
These instructions do not claim to cover all details or variations in the equipment, procedure, or process  
described, nor to provide directions for meeting every possible contingency during installation, operation or  
maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s  
purpose, please contact your nearest representative.  
 

Clarion Car Video System VT1000B User Manual
Clarion CD Player DB325am User Manual
Coleman Tent 2000007826 User Manual
Continental Refrigerator Refrigerator SW48 10C FB User Manual
Cooper Lighting Landscape Lighting CLB25MWW5C373 User Manual
Craftsman Blower 358794772 User Manual
Dynex Power Supply DX 400WPS User Manual
Electro Voice Stereo Amplifier AP2600 User Manual
FUNAI Flat Panel Television MJ414FG User Manual
Gateway Laptop E 155c User Manual